⚡ Connectors & Electronics

Connector machining — where the failures actually come from

On RF and electrical parts, the defects that cause field failures are almost never the ones covered by the general tolerance block:

  • a burr or rolled edge at the pin bore that survives plating and then breaks contact intermittently
  • a mating bore and an outer interface machined in different setups, so the two axes end up slightly apart
  • a burr left on a grounding or bonding face, which is exactly where the coating has to conduct

All three pass a check at the bench and fail later — usually after the parts are plated, because plating covers a burr and adds thickness where the fit was already tight.

That is why the pin bore, mating face, thread start and any grounding surface are treated as critical features here: machined from the same datum wherever the geometry allows, deburred before the parts go out for plating, and measured on the CMM with the values recorded on the report that ships with the order.

What we need to quote a connector or contact part

Send what you have — connector quotes are normally reviewed within 48 hours, and the ones that drag are missing the same items:

  • material and grade (brass C360, copper C110, beryllium copper, stainless 303)
  • plating spec from your connector datasheet — underplate and top plate, with thickness
  • which features are mating or contact surfaces
  • tolerance class on the thread and on the mating bore
  • quantity, and whether this is a prototype or a repeat of an existing part

A STEP file plus the plating call-out is enough to start if the drawing is not frozen yet.

Prototypes in days, repeat batches from the same setup

Prototypes ship 5–7 business days after drawing approval. Production timing is confirmed at RFQ, because plating lead time sits outside our machine shop — we machine, inspect and manage the coating, and we will not quote a date we cannot hold.

Once a part has run, the program, tooling notes and inspection plan stay on file, so a repeat order starts from your part number and quantity instead of from scratch.

Material and plating choices for contacts and housings

Brass C360 machines cleanly and is the usual choice for RF housings; copper C110 where conductivity leads; beryllium copper for spring contacts that have to hold force; stainless 303 for strength-critical hardware.

Gold, nickel, silver and tin plating are arranged with partner plating shops to your datasheet spec and re-inspected batch by batch for thickness, adhesion and appearance. Where a coating would close a fit, tell us which features must stay nominal — we machine the allowance in or leave the feature masked.

Capabilities at a Glance

Every number below is what we hold on your parts — CMM-verified, with free FAI on your first order.

Tolerance±0.005mm on critical dimensions
MaterialsBrass C360 for machinability · Copper C110 for conductivity · Beryllium copper for spring contacts · Stainless 303 for strength-critical hardware.
Process5-Axis Milling + Turning
Surface FinishBead Blasting · Passivation (available on request); plating (gold, nickel, silver, tin) arranged via our partners
InspectionCMM report with measured values · free FAI
Lead TimePrototypes 5–7 business days; production 3–5 months. DDP door-to-door with one invoice.

What to check before you order Connectors & Electronics

Most quote delays on Connectors & Electronics come from drawings that leave the material condition, the critical tolerances or the inspection documents open. These six points are confirmed before a price is issued.

  1. Material grade and condition: Brass C360 for machinability · Copper C110 for conductivity · Beryllium copper for spring contacts · Stainless 303 for strength-critical hardware.
  2. Critical dimensions and the tolerance tied to them: ±0.005 mm is what we hold where the drawing marks a feature critical.
  3. Surface roughness per functional face: Ra 1.6 µm is a typical as-machined value, and finer finishes are quoted on request.
  4. Surface treatment and masking: Bead Blasting · Passivation (available on request); plating (gold, nickel, silver, tin) arranged via our partners
  5. Quantity and delivery: Prototypes 5–7 business days; production 3–5 months. DDP door-to-door with one invoice.
  6. Inspection documents: a CMM report with measured values, a free first-article report on new parts, and material certificates on request.

Process window by part type

FeatureTypical toleranceSurface roughnessHow it is verified
RF connector housings±0.005 mmRa 1.6 µmCMM report, measured values
Contact pin holders±0.005 mmRa 1.6 µmFree FAI on new parts
Shielding parts±0.005 mmRa 1.6 µmIn-process check at each operation
Mating faces and bores±0.005 mmRa 1.6 µmCMM plus roughness check
  • RF connector housings for Connectors & Electronics are machined from Brass C360 for machinability and held to ±0.005 mm on critical dimensions.
  • Contact pin holders are checked in process at every operation and ship with a CMM report of measured values.
  • First articles for Connectors & Electronics come with a free inspection report, and material certificates are available on request.
  • Orders for Connectors & Electronics start at one piece, because quantity changes the unit price rather than the process.
  • The Dongguan plant that machines Connectors & Electronics holds ISO 9001:2015 certificate 93726Q00307R001.
  • Prototypes of Connectors & Electronics ship in 5–7 business days, and production runs are quoted DDP with one invoice.

Frequently Asked Questions

  • How do you hold concentricity between the mating bore and the outer interface?

    Both features are machined from the same datum wherever the geometry allows, and the result is measured on the CMM. Where a second setup is needed, the datum is re-established from the first — not from a vise mark.

  • How do you prevent burrs at the contact pin bores?

    Pin bores and thread starts are deburred before the parts go out for plating, and burr-sensitive features are checked at the bench rather than after coating. Once a burr is plated over it is invisible, and it still breaks contact.

  • Can you supply machined parts without plating, or arrange the plating for us?

    Both. Parts can ship machined and degreased for your own plating line, or go through our partner shops with the spec taken from your connector datasheet and re-inspected on return for thickness, adhesion and appearance.

  • What connector parts can you machine?

    RF coaxial connector bodies, contact pins and sockets, interconnect housings, insulator supports and precision threaded connector parts from brass and copper alloys.

  • What materials do you recommend for RF and electrical parts?

    Brass C360 for machinability, Copper C110 for conductivity, Beryllium copper for spring contacts, Stainless 303 for strength-critical hardware.

  • What tolerances do you hold on connector threads and mating features?

    ±0.005mm on critical dimensions with thread-form verification — connector threads, contact bores and alignment features are CMM-checked.

  • Can you apply plating to connector parts?

    Yes — plating (gold, nickel, silver, tin) is arranged with our trusted partners; parts are machined to accept the specified plating thickness.

  • What is your lead time for connector prototypes?

    3–5 months for production, prototypes in 5–7 business days. Fast track available on proven designs.

  • How do you ensure consistency in contact pin batches?

    In-process inspection, CMM sampling and measured values on critical dimensions, with full reports included on every order.

Buyer's Guide

  • How to Get a Quote for Connector & Electronic Parts

    Send the drawing with: material, conductivity or RF requirements, plating spec, quantity, and critical dimensions. Electrical function info helps us pick the right grade.

  • Material Selection Guide

    Brass C360 for machined bodies, C110 copper for high-conductivity paths, beryllium copper for contacts requiring spring properties, stainless 303 for hardware. Plating spec completes the picture.

  • Machinability tips for Connector Machining

    Specify thread and bore tolerances realistically, allow plating thickness in your finished dimensions, and avoid sharp internal edges that affect signal paths.

  • Quality & Inspection

    CMM inspection with full report, thread-form verification, measured values, free FAI. Batch consistency monitored across production lots.

  • Lead Time & Shipping

    Prototypes 5–7 business days, production 3–5 months. DDP door-to-door with one invoice — export, customs, duties, last-mile.

What drives the price of Connectors & Electronics

Connectors & Electronics is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.

Get a Quote for Connectors & Electronics

Send us your drawing — we review within 48h and return a quote with lead time.

Get a Quote →