CNC Milling: 3-Axis and 5-Axis Machining for Housings, Plates and Complex Geometries

CNC Milling at TruPart Precision (Dongguan, China) is quoted from the drawing: tolerance ±0.01 mm general, ±0.005 mm on critical features; surface finish Ra 0.8–3.2 μm (5-axis contour finishing to Ra 0.8); materials Aluminum, stainless, titanium, copper alloys, engineering plastics; batch 1–5,000+ (prototype to production). Every batch is verified — CMM, FAI report with measured values. A drawing review returns a quotation with unit price, machining route, lead time and freight within 48 hours, and there is no minimum order quantity.

  • TruPart Precision holds ±0.01 mm general, ±0.005 mm on critical features on CNC Milling work, and the measured values are reported per feature on a CMM.
  • Surface finish for CNC Milling is Ra 0.8–3.2 μm (5-axis contour finishing to Ra 0.8) as machined; finer finishes are quoted on request rather than assumed.
  • Materials used for CNC Milling: Aluminum, stainless, titanium, copper alloys, engineering plastics.
  • Batch sizes for CNC Milling range 1–5,000+ (prototype to production) — quantity changes the unit price rather than the process.
  • Inspection for CNC Milling: CMM, FAI report with measured values.
  • CNC Milling at TruPart Precision is quoted from the drawing; a prototype is priced on the same route as a production batch.
  • The Dongguan plant that machines CNC Milling holds ISO 9001:2015 certificate 93726Q00307R001.

What We Hold on Your Parts

Every number above is what we hold on your parts — CMM-verified, with free FAI on your first order.

Tolerance±0.01 mm general, ±0.005 mm on critical features
Surface finishRa 0.8–3.2 μm (5-axis contour finishing to Ra 0.8)
Machines3-axis VMC and 5-axis machining centers
PartsPlates, housings, valve blocks, brackets, impellers, molds
MaterialsAluminum, stainless, titanium, copper alloys, engineering plastics
Batch1–5,000+ (prototype to production)
InspectionCMM, FAI report with measured values

Procurement facts — fixed before you order

ItemWhat is fixed
Minimum orderNo minimum order quantity. A single part and a production batch run through the same route.
QuotationWithin 48 hours of a drawing or STEP file: unit price, machining route, setup, packed weight and freight itemised.
Prototype lead time5–7 business days after drawing approval.
Production lead timeConfirmed per part and quantity in the quotation, not a catalogue figure.
IncotermsEXW, DDP or air. Freight is quoted before the order, not billed after it.
DocumentationMaterial certificate to EN 10204 3.1 with mill and heat number; CMM report with measured values; FAI report on a new part.

Batch range as stated on this page: 1–5,000+ (prototype to production)

What moves the unit price of CNC milling

A machined part is priced by the work it contains, not by its weight. Five drivers move the number, in this order of magnitude:

Cost driverRises whenEffect on unit price
SetupsFeatures sit on more than one face, or the datum has to be re-establishedHigh
Tolerance±0.005 mm appears on every dimension instead of only the critical onesMedium to high
Stock removalThe part is cut from solid bar or plate instead of a near-net blankMedium
Surface finishRa 0.4 µm or tighter, or a coating applied after machiningMedium
Batch sizeOne part carries the whole setup; 100 parts share itHigh at quantity 1, falls with volume

These are magnitudes, not prices. The quotation carries the actual numbers for your drawing, line by line.

What the quotation contains

Line in the quotationWhy it matters
Unit price at your quantityThe same part at 1, 100 and 1,000 pieces priced separately
Setup and tooling, listed separatelyOne-time charges are not folded into the unit price
Machining route and lead timeYou see which operations decide the date
Packed weight and carton sizeFreight can be calculated before you commit
Freight: EXW, DDP or airLanded cost known before the order
  • CNC milling at TruPart Precision holds tolerances of ±0.01 mm general, ±0.005 mm on critical features — measured on a CMM and reported as measured values with every batch.
  • A machined part is priced by setups, stock removal and tolerance, not by its weight.
  • TruPart Precision returns a CNC milling quotation within 48 hours of a drawing, with the machining route and freight itemised.

What actually decides the price of a milled part

A milled part is not priced by its weight. It is priced by how many setups the geometry forces, how much of the stock ends up as chips, and how tight the critical callouts are. Two plates with the same outline can differ several times over on those three points alone.

  • Setups: features on five faces mean one 5-axis setup instead of three re-clamps and a fixture for each
  • Material removal: a part cut from solid plate carries cutting time that a near-net blank or a casting would not
  • Tolerances: ±0.005 mm on critical features is routine; the same callout on every dimension adds inspection time without adding function

Send the drawing and we will tell you which of the three is driving your price, with the machining route behind it, within 48 hours.

The questions that come with every milling enquiry

Milling enquiries arriving from the US, Canada and the EU ask for the same things, and all of them belong in the quotation rather than in a follow-up email.

  • Shipping cost and delivery time up front — EXW, DDP or air, on the same page as the unit price
  • A cost breakdown by raw material, machining, tapping and finishing rather than one lump sum
  • One-time setup and tooling charges listed separately, with packed weight and carton dimensions
  • Mill certificates to EN 10204 3.1 naming the mill and the heat number
  • A quantity ladder at the volumes you actually order — prototype, then 500, then the annual figure

Where a milled part is a repeat, the fixture and the setup sheet stay on file, so the second batch is quoted from the route that has already run instead of being re-estimated.

The one decision that changes the geometry of your part

A part with pockets on one face and a flat back is a 3-axis job. A part whose bores, sealing faces or contoured faces sit at compound angles is a 5-axis job, because every extra re-clamp adds a datum error on top of the tolerance you asked for.

  • One setup: bores, sealing faces and mounting holes cut from the same datum
  • Compound angles: no angled fixture and no second operation
  • Deep pockets and thin walls: roughing and finishing strategies that keep deflection out of the final dimension

Valve bodies, manifolds, fixture plates and covers are the milled parts that move to 5-axis most often. Flat plates and brackets usually stay on 3-axis, which keeps the price down.

One plate or five hundred — the same report

Every milled batch ships with a CMM dimensional report listing measured values on the critical features, and a free first article inspection report on a new part. Material certificates to EN 10204 3.1 ship with the batch.

Around 70% of the part requests that reach us are for 1–100 pieces, so a single milled plate is normal work here rather than an exception. There is no minimum order quantity, and where the order is DDP one invoice covers export, freight, customs and delivery.

From our historical RFQ data, around 70% of incoming part requests fall within 1–100 pieces. We support both prototype batches and volume production with no minimum-order requirement. Submit your drawing for feasibility evaluation.

What to send for a milling quotation

A milled part is priced on setups and cutting time. Both are visible on the drawing before a machine is touched.

  1. Drawing and 3D model, with the datum scheme marked
  2. The features that carry ±0.005 mm, separated from the general dimensions
  3. Number of faces that have to be machined, since each re-clamp adds a setup
  4. Material and whether the mill certificate to EN 10204 3.1 is required
  5. Quantity at the volumes you actually order — prototype, pilot, annual
  6. Surface finish and any post-process, with the areas that must not be finished
  7. Whether the part fits an existing assembly, and which dimensions must match it

Send what you have — a model without a drawing, or a drawing without a model, is enough to start the review.

Frequently Asked Questions

  • What does a milling quotation contain?

    Unit price at your quantity, the machining route and lead time, setup and tooling charges where they apply, packed weight and carton dimensions, and shipping cost up front — EXW, DDP or air. Material certificates to EN 10204 3.1 ship with the batch.

  • Can you hold ±0.005 mm on a milled part?

    ±0.005 mm on critical features is routine, verified on a CMM and reported as measured values with the batch, together with a free first article inspection report on a new part.

  • Why is a milled part more expensive than the material cost suggests?

    Price follows setups and cutting time, not weight. A part that needs three re-clamps and a fixture, or carries ±0.005 mm on every dimension, contains work that the raw material figure never shows. We say which of those is driving your price at drawing review, before the order is placed.

  • What tolerance can CNC milling hold?

    ±0.01 mm as general, ±0.005 mm on carefully set up critical features. Positions and contours are verified on the CMM.

  • When do I need 5-axis instead of 3-axis?

    When features exist on multiple faces and compound angles — 5-axis machines them in one setup, eliminating re-clamping error and extra fixture cost.

  • Can you mill thin walls without deflection?

    Yes, with controlled tool paths and workholding; we flag unstable geometry at drawing review before quoting.

  • What materials do you mill?

    Aluminum 6061/7075, stainless 303/304/316, titanium, brass/copper, PEEK/POM/ABS — all with CMM-verified tolerances.

  • Do you do small-batch milling?

    Yes, no MOQ. Single prototypes, pilot runs and production quantities, with free FAI on every new part.

What buyers actually asked us this autumn

Verbatim lines from enquiries received between August and November 2026; buyer names and companies are withheld. Lines without quotation marks are summarised from the drawing or from the buyer’s own email.

Four part drawings with quantity bands, sent back the same day we asked.

Buyer reply to our EDM · precision engineering, Singapore · Sep 2026

What drives the price of CNC Milling

CNC Milling is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.

Have a Similar Part in Mind?

Send us your drawing — we review within 48h and return a quote with lead time.

Get a Quote →