Swiss Machining: What Small, Long and Complex Precision Parts Can You Produce?

Swiss Machining at TruPart Precision (Dongguan, China) is quoted from the drawing: tolerance ±0.005 mm on critical diameters; surface finish Ra 0.4–0.8 μm; materials Aluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, PEEK/POM; batch From prototype to high-volume production. Every batch is verified — CMM, FAI report with measured values. A drawing review returns a quotation with unit price, machining route, lead time and freight within 48 hours, and there is no minimum order quantity.

  • TruPart Precision holds ±0.005 mm on critical diameters on Swiss Machining work, and the measured values are reported per feature on a CMM.
  • Surface finish for Swiss Machining is Ra 0.4–0.8 μm as machined; finer finishes are quoted on request rather than assumed.
  • Materials used for Swiss Machining: Aluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, PEEK/POM.
  • Batch sizes for Swiss Machining range From prototype to high-volume production — quantity changes the unit price rather than the process.
  • Inspection for Swiss Machining: CMM, FAI report with measured values.
  • Swiss Machining at TruPart Precision is quoted from the drawing; a prototype is priced on the same route as a production batch.
  • The Dongguan plant that machines Swiss Machining holds ISO 9001:2015 certificate 93726Q00307R001.

What We Hold on Your Parts

Every number below is what we hold on your parts — CMM-verified, with free FAI on your first order.

Tolerance±0.005 mm on critical diameters
Surface finishRa 0.4–0.8 μm
Size rangeSmall diameters, long thin parts — send your drawing for a feasibility review
MaterialsAluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, PEEK/POM
EquipmentSwiss-type turning capacity
BatchFrom prototype to high-volume production
InspectionCMM, FAI report with measured values

Procurement facts — fixed before you order

ItemWhat is fixed
Minimum orderNo minimum order quantity. A single part and a production batch run through the same route.
QuotationWithin 48 hours of a drawing or STEP file: unit price, machining route, setup, packed weight and freight itemised.
Prototype lead time5–7 business days after drawing approval.
Production lead timeConfirmed per part and quantity in the quotation, not a catalogue figure.
IncotermsEXW, DDP or air. Freight is quoted before the order, not billed after it.
DocumentationMaterial certificate to EN 10204 3.1 with mill and heat number; CMM report with measured values; FAI report on a new part.

Batch range as stated on this page: From prototype to high-volume production

What moves the unit price of Swiss-type turning

A machined part is priced by the work it contains, not by its weight. Five drivers move the number, in this order of magnitude:

Cost driverRises whenEffect on unit price
SetupsFeatures sit on more than one face, or the datum has to be re-establishedHigh
Tolerance±0.005 mm appears on every dimension instead of only the critical onesMedium to high
Stock removalThe part is cut from solid bar or plate instead of a near-net blankMedium
Surface finishRa 0.4 µm or tighter, or a coating applied after machiningMedium
Batch sizeOne part carries the whole setup; 100 parts share itHigh at quantity 1, falls with volume

These are magnitudes, not prices. The quotation carries the actual numbers for your drawing, line by line.

What the quotation contains

Line in the quotationWhy it matters
Unit price at your quantityThe same part at 1, 100 and 1,000 pieces priced separately
Setup and tooling, listed separatelyOne-time charges are not folded into the unit price
Machining route and lead timeYou see which operations decide the date
Packed weight and carton sizeFreight can be calculated before you commit
Freight: EXW, DDP or airLanded cost known before the order
  • Swiss-type turning at TruPart Precision holds tolerances of ±0.005 mm on critical diameters — measured on a CMM and reported as measured values with every batch.
  • A machined part is priced by setups, stock removal and tolerance, not by its weight.
  • TruPart Precision returns a Swiss-type turning quotation within 48 hours of a drawing, with the machining route and freight itemised.

From our historical RFQ data, around 70% of incoming part requests fall within 1–100 pieces. We support both prototype batches and volume production with no minimum-order requirement. Submit your drawing for feasibility evaluation.

Typical Parts We Machine on Swiss-Type

Real demand from our RFQ inbox — long slender and small-diameter parts are among the most frequent requests we receive for Swiss-type work, mostly for connectors, instruments and precision hardware.

  • Long slender shafts and small-diameter pins
  • Fasteners and threaded prec

    Swiss-type turning — where slender parts actually fail

    A long, thin part rarely fails on the drawing. It fails on the machine, because the tool pushes the workpiece away from the cut and the diameter drifts along the length. Swiss-type turning removes that failure mode: bar stock feeds through a guide bushing, so the cut happens millimetres from the support point instead of at the end of a long overhang.

    • Deflection controlled by cutting close to the guide bushing, not by slowing the cycle down
    • Diameter and concentricity held along the full length of the part, not just at the chuck
    • Secondary operations (cross-drilling, slotting, threading) done in the same cycle where the geometry allows

    The practical effect for a buyer: a slender part that comes back bent, tapered or out of round after a conventional turning route is usually a Swiss-type job.

    What we need to quote a Swiss-type part

    Swiss work is quoted from the part, not from a catalogue, because the bar diameter, the unsupported length and the tolerance band decide the cycle and the tooling. Send these and we answer with routing, price and lead time within 48 hours.

    • Drawing with diameter, length and the tolerance band on each turned feature
    • Material — stainless 303/304/316, aluminium, brass, titanium and engineering plastics all run on this route
    • The longest unsupported length and the smallest diameter on the part
    • Quantity: prototype, first batch and expected repeat volume
    • Any cross-hole, flat, slot or thread that has to be produced in the same cycle

    If your part is borderline between Swiss-type and conventional turning, send both the drawing and the annual volume — we will quote the route that holds the tolerance at the lowest cost, and say which one it is.

    From one sample to a repeat batch

    Around 70% of the part requests that reach us are for 1–100 pieces, and small-diameter Swiss work is a large share of those. A single sample part goes through the same first article inspection as a production lot: dimensional report, measured values on the critical diameters, material documentation on request.

    Repeat batches get easier, not harder, because the programme and the bar setup are already proven. Tell us the annual volume with the first enquiry and we will price the repeat level along with the prototype.

    Material and finish choices for small turned parts

    Most Swiss-type work we run is stainless — 303 for free-machining parts, 304 and 316 where corrosion resistance matters — alongside aluminium, brass, titanium and plastics such as PEEK and POM for instrument and connector components.

    Turned parts can be finished in the same plant: passivation and pickling for stainless, anodizing for aluminium, plating where the drawing calls for it. Small parts are handled and packed individually where the finish is cosmetic.

    ision hardware
  • Connector pins and instrument components

Have a similar small or slender part? Send your drawing — we confirm the right process and feasibility within 48h.

What to send for a Swiss-type quotation

A Swiss-type part is priced on the bar diameter, the length-to-diameter ratio and the number of secondary operations.

  1. Maximum outside diameter and overall length, so the bar size and the guide bushing are fixed
  2. Length-to-diameter ratio, because slender parts need support and slower passes
  3. Cross-drilled holes, flats and slots, and whether they can be done in the same setup
  4. Tolerance on diameter, concentricity and position, feature by feature
  5. Material and the bar availability in that diameter, which decides the lead time
  6. Whether the visible guide-bushing marks are acceptable on the finished surface
  7. Quantity and repeat pattern, so the programme and the tooling stay on file

Send what you have — a model without a drawing, or a drawing without a model, is enough to start the review.

Frequently Asked Questions

  • Can you run Swiss-type work on very small diameters?

    Small diameters and long slender geometries are exactly what this route is for. Send the drawing with the smallest diameter and the longest unsupported length, and we will confirm feasibility and bar availability within 48 hours rather than quoting a geometry we cannot hold.

  • How do you keep a long shaft straight and concentric?

    By cutting close to the guide bushing, so the tool never pushes the workpiece away from the support point, and by keeping the part supported for as much of the cycle as the geometry allows. Diameter and runout are then verified on the CMM, with the measured values reported on the critical features.

  • Do you machine parts that need cross-holes or a thread as well as turning?

    Yes. Cross-drilling, slotting, flat milling and threading can be produced in the same cycle where the geometry and the tooling allow, which avoids a second setup and the positional error that comes with it. Complex features are evaluated at drawing review and confirmed in the quotation.

  • What is Swiss machining?

    A turning method where bar stock feeds through a guide bushing so the tool cuts close to the support point. This eliminates deflection on long, thin parts — the reason Swiss-type machines are the default for small, slender components with tight tolerances.

  • When is Swiss machining better than standard turning?

    For parts with a high length-to-diameter ratio (roughly above 3:1) and small diameters, standard turning centers cannot hold accuracy because the workpiece deflects under cutting force. Swiss machining supports the material within millimeters of the cut and holds the tolerance without chatter.

  • What tolerances can Swiss machining hold?

    ±0.005 mm on critical diameters, verified on a CMM with a full report. General dimensions run at ±0.05–0.1 mm unless specified.

  • What materials can be Swiss-machined?

    Aluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, and engineering plastics such as PEEK and POM. Small diameters in these materials are routine for connector and instrument components.

  • What batch sizes suit Swiss machining?

    Swiss-type capacity runs from pilot quantities to high-volume production — the process is stable across long runs, which is why it is standard for connector pins, fasteners and instrument parts.

  • How do I get a feasibility check for my part?

    Send your drawing or STEP file — we review the diameter, length and features within 48h and confirm whether Swiss machining is the right process before quoting.

What drives the price of Swiss Machining

Swiss Machining is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.

Have a Similar Part in Mind?

Send us your drawing — we review within 48h and return a quote with lead time.

Get a Quote →