CNC Machining Tolerances — Complete Guide

What tolerance can TruPart achieve?

TruPart Precision achieves tolerances as tight as ±0.005mm (±0.0002in) on critical dimensions using 5-axis machining centres and CMM inspection. Standard precision is ±0.1mm for non-critical features.

ISO 2768 Tolerance Classes

ClassToleranceTypical Use
Fine (f)±0.05mmPrecision fits, mating surfaces
Medium (m)±0.1mmGeneral engineering
Coarse (c)±0.3mmNon-critical features
Very Coarse (v)±1.0mmRough dimensions

When tight tolerance costs more

A part at ±0.005mm typically costs 30-50% more than ±0.1mm due to slower cutting speeds, additional setups, and CMM time. We'll always recommend the most cost-effective tolerance for your application.

Factors Affecting Tolerance

  • Material: Aluminum holds tighter tolerances than plastics or superalloys
  • Geometry: Simple turned parts are easier than complex 5-axis parts
  • Surface finish: Ra 0.4μm requires slower finishing passes
  • Heat treatment: Parts may shift slightly after treatment

Which tolerance callouts actually drive the price

Two drawings of the same part can quote 30–50% apart, and the difference is almost never the material. It is which dimensions carry a tight band. A tight tolerance on a critical bore is normal work; the same band applied to a clearance hole or an outer profile buys nothing and slows the whole route down.

  • Critical fits, mating surfaces and locating bores: hold the tight band, inspect and report it
  • Clearance holes, outer profiles and non-functional radii: a general tolerance is enough
  • Geometry that forces extra setups or slow finishing passes drives cost faster than the tolerance figure itself

When a callout looks tighter than the function needs, we say so at drawing review and quote the cost-effective band alongside the one you specified.

How a tight tolerance is verified before it ships

A tolerance is only worth what the inspection behind it proves. Critical dimensions are measured on the CMM and reported as actual measured values, not as a pass/fail stamp, so incoming inspection at your end can be compared against real numbers.

A new part gets a free first article inspection report covering dimensions, material and surface finish. Threads and seal faces are checked with the gauges and mating parts used in assembly, and EN 10204 3.1 mill certificates are available on request for full traceability from raw material to finished part.

Where a tight tolerance is wasted money

Tolerances are cumulative in cost: a tighter band means slower cutting, more finishing passes, more heat control and more CMM time. Where a feature has no functional partner, that money does not come back as a better part.

The practical rule we apply at drawing review: tight on what mates, general on what does not. If your design requires a tight band everywhere for an assembly reason we cannot see, tell us — there is usually one or two features that actually carry it.

Tolerances after heat treatment and coating

Heat treatment moves a part, and coating adds material to it. Both have to be planned into the tolerance stack before machining starts: hardened parts are machined with a grinding allowance where the drawing requires the final tolerance after treatment, and plated or anodized surfaces are either masked or sized for the coating thickness.

Tell us the inspection stage — before or after treatment — and the callouts will be set up for that stage, not adjusted afterwards.

Frequently Asked Questions

  • Can you hold ±0.005 mm on every dimension of the part?

    ±0.005 mm is applied to critical dimensions, not to the whole drawing — a part held that tight everywhere is slower and more expensive for no functional gain. We confirm at drawing review which features carry the tight band and which are covered by the general tolerance.

  • Do you report actual measured values or just a pass/fail result?

    Measured values. Critical dimensions are inspected on the CMM with the actual numbers reported, alongside a free first article inspection report on a new part. That way your incoming inspection compares against real values instead of a certificate that only says the part passed.

  • What happens to the tolerance when the part is heat treated or plated?

    Both are planned into the route before machining. Parts that are hardened are cut with a grinding allowance where the drawing requires the final tolerance after treatment, and surfaces that are anodized or plated are either masked or machined to suit the coating thickness. Tell us whether inspection happens before or after treatment and we will set the callouts for that stage.

What buyers actually asked us this autumn

Verbatim lines from enquiries received between August and November 2026; buyer names and companies are withheld. Lines without quotation marks are summarised from the drawing or from the buyer’s own email.

16 µin Ra on the outer cylindrical surface, 0.0005 in geometric tolerance, and a 1/4-28 UNF thread the buyer would not relax.

Buyer confirmation after quotation · motion-control parts, United States · Sep 2026

Aluminium cap to ±0.02 mm with an as-machined finish, and a steel tube hot-dip galvanised.

Buyer reply to our EDM · furniture hardware, Türkiye · Sep 2026

Discuss Your Tolerance Requirements

Send your drawing with tolerance callouts — we'll advise the most cost-effective approach.

Get a Quote →