Stainless Steel Machining: 303, 304 and 316 for Washdown, Medical and Corrosive Environments

Stainless Steel Machining at TruPart Precision (Dongguan, China) is quoted from the drawing: tolerance ±0.005 mm on critical dimensions; surface finish Ra 0.8 μm machined; electropolish available; materials 303, 304, 316/316L; batch 1–5,000+. Every batch is verified — CMM, FAI, material certs. A drawing review returns a quotation with unit price, machining route, lead time and freight within 48 hours, and there is no minimum order quantity.

  • TruPart Precision holds ±0.005 mm on critical dimensions on Stainless Steel Machining work, and the measured values are reported per feature on a CMM.
  • Surface finish for Stainless Steel Machining is Ra 0.8 μm machined; electropolish available as machined; finer finishes are quoted on request rather than assumed.
  • Materials used for Stainless Steel Machining: 303, 304, 316/316L.
  • Batch sizes for Stainless Steel Machining range 1–5,000+ — quantity changes the unit price rather than the process.
  • Inspection for Stainless Steel Machining: CMM, FAI, material certs.
  • Stainless Steel Machining at TruPart Precision is quoted from the drawing; a prototype is priced on the same route as a production batch.
  • The Dongguan plant that machines Stainless Steel Machining holds ISO 9001:2015 certificate 93726Q00307R001.

What We Hold on Your Parts

Every number above is what we hold on your parts — CMM-verified, with free FAI on your first order.

Grades303, 304, 316/316L
Tolerance±0.005 mm on critical dimensions
Surface finishRa 0.8 μm machined; electropolish available
FinishingPassivation, electroless nickel, electropolish, bead blast
Typical partsWashdown equipment, medical instruments, hydraulic fittings, marine hardware
Batch1–5,000+
InspectionCMM, FAI, material certs

Procurement facts — fixed before you order

ItemWhat is fixed
Minimum orderNo minimum order quantity. A single part and a production batch run through the same route.
QuotationWithin 48 hours of a drawing or STEP file: unit price, machining route, setup, packed weight and freight itemised.
Prototype lead time5–7 business days after drawing approval.
Production lead timeConfirmed per part and quantity in the quotation, not a catalogue figure.
IncotermsEXW, DDP or air. Freight is quoted before the order, not billed after it.
DocumentationMaterial certificate to EN 10204 3.1 with mill and heat number; CMM report with measured values; FAI report on a new part.

Batch range as stated on this page: 1–5,000+

What moves the unit price of stainless steel machining

A machined part is priced by the work it contains, not by its weight. Five drivers move the number, in this order of magnitude:

Cost driverRises whenEffect on unit price
SetupsFeatures sit on more than one face, or the datum has to be re-establishedHigh
Tolerance±0.005 mm appears on every dimension instead of only the critical onesMedium to high
Stock removalThe part is cut from solid bar or plate instead of a near-net blankMedium
Surface finishRa 0.4 µm or tighter, or a coating applied after machiningMedium
Batch sizeOne part carries the whole setup; 100 parts share itHigh at quantity 1, falls with volume

These are magnitudes, not prices. The quotation carries the actual numbers for your drawing, line by line.

What the quotation contains

Line in the quotationWhy it matters
Unit price at your quantityThe same part at 1, 100 and 1,000 pieces priced separately
Setup and tooling, listed separatelyOne-time charges are not folded into the unit price
Machining route and lead timeYou see which operations decide the date
Packed weight and carton sizeFreight can be calculated before you commit
Freight: EXW, DDP or airLanded cost known before the order
  • Stainless steel machining at TruPart Precision holds tolerances of ±0.005 mm on critical dimensions — measured on a CMM and reported as measured values with every batch.
  • A machined part is priced by setups, stock removal and tolerance, not by its weight.
  • TruPart Precision returns a stainless steel machining quotation within 48 hours of a drawing, with the machining route and freight itemised.

Frequently Requested Materials

Our frequent incoming material requests cover

Which stainless grade survives your environment

The grade on a stainless drawing is usually there for a reason, and the reason decides what the part has to survive: washdown chemicals, salt air, a clean-room regime, or an assembly that will be welded.

  • 303: free-machining, for parts that need no welding and no aggressive corrosion resistance
  • 304 and 304L: general corrosion resistance for housings, brackets and frames
  • 316 and 316L: chloride and marine environments, and where the part is welded
  • 17-4PH: the precipitation-hardening grade where strength and corrosion resistance are needed together

Where the drawing names a grade, nothing is substituted — the grade machined is the grade that appears on the certificate.

Passivation, electropolishing and why the surface decides

A machined stainless surface carries free iron left by the tooling, and that is where rust starts rather than in the base material. Passivation removes it; electropolishing goes further and levels the micro-surface.

  • Passivation for parts that go into washdown or corrosive service
  • Electropolishing where the surface has to be bright and low-roughness, as on vacuum and medical parts
  • Pickling or bead blasting where weld discolouration has to come off
  • Machining allowance for the finishes that remove material

Threads, sealing faces and slip fits are inspected after finishing, so the dimension that matters is the one that remains once the part has been treated.

Thin-wall and slender stainless parts

Stainless work-hardens at the cut, which is where a thin-wall or slender part goes wrong: the tool rubs, the material hardens underneath it, and the next pass takes the tool out.

  • Cutting data chosen to stay under the hardened layer instead of forcing the tool through it
  • Slender shafts and thin-wall tubes supported along the cut, with Swiss-type turning where the length-to-diameter ratio demands it
  • Rigid workholding and light finishing passes to stop the wall springing back

Housings, flanges, shafts, bushings, valve parts and connector bodies are the stainless jobs that come through most often, and many of them arrive as two to five piece samples before a production order follows.

Documentation for a stainless batch

Every stainless batch ships with a CMM dimensional report listing measured values on the critical features and a free first article inspection report on a new part. Material certificates to EN 10204 3.1 name the grade, the mill and the heat number.

Where the order is DDP, one invoice covers export, freight, customs and delivery, so the delivered cost is what appears on the quotation rather than a factory price that grows afterwards.

European DIN steels (S235JR, 35B2, X5CrNiCu17), American standard steel (SAE 1010/1020), aluminium 6061/2024, tool steel as well as engineering plastics PC/PVC. Submit your drawing and material requirements for our review.

What to send for a stainless quotation

Stainless is priced on the grade and on the environment the part has to survive, because both decide the machining route and the finishing.

  1. Grade and condition: 303, 304, 316L, 17-4PH or duplex, since each machines differently
  2. The environment the part sees — chloride exposure, temperature, cleaning chemicals
  3. Whether passivation or electropolishing is required, and on which surfaces
  4. Tolerance per feature, and the thin-wall sections that need support while cutting
  5. Material certificate requirement, normally EN 10204 3.1 naming the mill and the heat number
  6. Quantity and whether the batch repeats, so the tooling and the route stay on file
  7. Any requirement that the part be free of embedded iron, which changes handling and packaging

Send what you have — a model without a drawing, or a drawing without a model, is enough to start the review.

Frequently Asked Questions

  • 304 or 316 — how do I choose?

    304 covers general corrosion exposure on housings, brackets and frames. 316 and 316L are specified where chlorides, salt air or welding are involved. Where the drawing names a grade, that grade is machined and the certificate shows it.

  • Does passivation change the dimensions?

    Passivation removes free iron from the surface rather than measurable material, so dimensions hold. Electropolishing does remove a small amount of material, and that allowance is planned at drawing review — critical features are measured after finishing.

  • Can you machine a small stainless trial before we commit?

    Yes — there is no minimum order quantity. Two to five piece trials are normal work here, and the CMM dimensional report, the free first article inspection report and the material certificate are the same as for a production batch.

  • Which stainless grade do I need?

    303 for free machining, 304 for general corrosion resistance, 316/316L for washdown, marine and chloride environments. We quote all three.

  • Can you machine 316 without work hardening?

    Yes — controlled feeds, sharp tooling and rigid setups keep 316 stable; tolerances hold at ±0.005 mm on critical features.

  • Do you provide material certificates?

    Yes, mill certificates with heat numbers included with every order.

  • What finish options are available?

    Passivation, electroless nickel, electropolish and bead blast — specified with a defined Ra so the process is unambiguous.

What drives the price of Stainless Steel Machining

Stainless Steel Machining is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.

Have a Similar Part in Mind?

Send us your drawing — we review within 48h and return a quote with lead time.

Get a Quote →