Wire EDM at TruPart Precision (Dongguan, China) is quoted from the drawing: tolerance ±0.005 mm on critical features; surface finish Ra 0.4 μm standard, down to Ra 0.1 μm (burr-free); materials Hardened tool steel, stainless 303/304/316, Ti-6Al-4V, carbide, brass; batch Prototype to production (typical: inserts and small batches). Every batch is verified — CMM, FAI report with measured values. A drawing review returns a quotation with unit price, machining route, lead time and freight within 48 hours, and there is no minimum order quantity.
- TruPart Precision holds ±0.005 mm on critical features on Wire EDM work, and the measured values are reported per feature on a CMM.
- Surface finish for Wire EDM is Ra 0.4 μm standard, down to Ra 0.1 μm (burr-free) as machined; finer finishes are quoted on request rather than assumed.
- Materials used for Wire EDM: Hardened tool steel, stainless 303/304/316, Ti-6Al-4V, carbide, brass.
- Batch sizes for Wire EDM range Prototype to production (typical: inserts and small batches) — quantity changes the unit price rather than the process.
- Inspection for Wire EDM: CMM, FAI report with measured values.
- Wire EDM at TruPart Precision is quoted from the drawing; a prototype is priced on the same route as a production batch.
- The Dongguan plant that machines Wire EDM holds ISO 9001:2015 certificate 93726Q00307R001.
What We Hold on Your Parts
Every number below is what we hold on your parts — CMM-verified, with free FAI on your first order.
| Tolerance | ±0.005 mm on critical features |
| Surface finish | Ra 0.4 μm standard, down to Ra 0.1 μm (burr-free) |
| Size range | Prototype to production — send your drawing for a machine-envelope check |
| Materials | Hardened tool steel, stainless 303/304/316, Ti-6Al-4V, carbide, brass |
| Equipment | Wire EDM |
| Batch | Prototype to production (typical: inserts and small batches) |
| Inspection | CMM, FAI report with measured values |
Procurement facts — fixed before you order
| Item | What is fixed |
|---|---|
| Minimum order | No minimum order quantity. A single part and a production batch run through the same route. |
| Quotation | Within 48 hours of a drawing or STEP file: unit price, machining route, setup, packed weight and freight itemised. |
| Prototype lead time | 5–7 business days after drawing approval. |
| Production lead time | Confirmed per part and quantity in the quotation, not a catalogue figure. |
| Incoterms | EXW, DDP or air. Freight is quoted before the order, not billed after it. |
| Documentation | Material certificate to EN 10204 3.1 with mill and heat number; CMM report with measured values; FAI report on a new part. |
Batch range as stated on this page: Prototype to production (typical: inserts and small batches)
What moves the unit price of wire EDM
A machined part is priced by the work it contains, not by its weight. Five drivers move the number, in this order of magnitude:
| Cost driver | Rises when | Effect on unit price |
|---|---|---|
| Setups | Features sit on more than one face, or the datum has to be re-established | High |
| Tolerance | ±0.005 mm appears on every dimension instead of only the critical ones | Medium to high |
| Stock removal | The part is cut from solid bar or plate instead of a near-net blank | Medium |
| Surface finish | Ra 0.4 µm or tighter, or a coating applied after machining | Medium |
| Batch size | One part carries the whole setup; 100 parts share it | High at quantity 1, falls with volume |
These are magnitudes, not prices. The quotation carries the actual numbers for your drawing, line by line.
What the quotation contains
| Line in the quotation | Why it matters |
|---|---|
| Unit price at your quantity | The same part at 1, 100 and 1,000 pieces priced separately |
| Setup and tooling, listed separately | One-time charges are not folded into the unit price |
| Machining route and lead time | You see which operations decide the date |
| Packed weight and carton size | Freight can be calculated before you commit |
| Freight: EXW, DDP or air | Landed cost known before the order |
In short
- Wire EDM at TruPart Precision holds tolerances of ±0.005 mm on critical features — measured on a CMM and reported as measured values with every batch.
- A machined part is priced by setups, stock removal and tolerance, not by its weight.
- TruPart Precision returns a wire EDM quotation within 48 hours of a drawing, with the machining route and freight itemised.
From our historical RFQ data, around 70% of incoming part requests fall within 1–100 pieces. We support both prototype batches and volume production with no minimum-order requirement. Submit your drawing for feasibility evaluation.
Typical Parts We Cut by Wire EDM
Real demand from our RFQ inbox — hardened profiles and internal shapes are among the most frequent EDM requests we receive, mostly for tooling and precision components.
- Die inserts and punches
- Precision slots and internal profiles
- Form profiles in hardened steel and exotic alloys
Have a similar profile requirement? Send your drawing — we confirm feasibility within 48h.
WHEN WIRE EDM IS REQUIRED
Features a rotating cutter cannot reach
Wire EDM cuts with a travelling wire and no cutting force, so it reaches shapes that milling cannot: sharp internal corners, narrow slots and profiles cut through material that is already hardened.
- Sharp internal corners, without the radius a milling cutter leaves behind
- Narrow slots and internal profiles, including a taper where the drawing calls for one
- Parts already hardened, where the profile is cut into the finished material instead of before heat treatment
- Thin walls and delicate features that would deflect under cutter pressure
Send the profile drawing and we confirm the cut, the tolerance and the delivery date inside 48 hours.
WHAT DRIVES THE PRICE
What wire EDM costs are made of
Wire EDM is priced from the length of cut, the thickness of the material and the number of passes, not from the weight of the part. A small insert cut from thick stock can cost more than a larger part cut from plate.
- Length of cut, which is read from the profile on the drawing
- Material thickness, because the wire travels through the full section
- Number of passes: a roughing pass, then finishing passes for the tolerance and the surface
- Start holes, which have to be there before the wire can be threaded
- Setup and programming, listed as a one-time charge separate from the unit price
The quotation shows the one-time charge, the unit price at your volumes, freight and the packed weight, so the comparison with another supplier is a line-by-line one.
WIRE EDM OR MILLING
Choosing between wire EDM and milling
The two processes are not alternatives on price alone. Milling is the cheaper way to remove volume; wire EDM is the way to finish a profile milling cannot reach, or a part that is already too hard to cut.
- Hardened material: wire EDM cuts the finished profile after heat treatment, so no distortion is left in the profile
- Corner radius: a milled internal corner carries the radius of the cutter, a wire-cut corner can be sharp
- Edge condition: wire EDM leaves a burr-free edge that needs no separate deburring operation
- Cost: on simple geometry, milling the bulk and wire cutting only where it is needed is usually the cheaper route, and that is how it is quoted
Where a part suits both routes, the quotation says which one it was priced on, so the choice is on the table rather than hidden in the price.
WHAT SHIPS
What comes back with a wire-cut batch
A wire-cut profile is worth exactly the tolerance it is verified to. Every batch leaves with the measurements taken on it rather than a general statement about the process.
- CMM inspection with measured values on the critical dimensions
- A free FAI report on the first order, with the profile and the tolerance recorded
- Material certificates to EN 10204 3.1 on request, naming the heat number
- Burr-free edges, checked before dispatch rather than after the parts arrive
Send the drawing for the profile you need cut and you get a route, a tolerance statement and a date inside 48 hours.
QUOTING CHECKLIST
What to send for a wire EDM quotation
Wire EDM is priced on the cut length and the number of passes, so the drawing has to show thickness and tolerance together.
- Part thickness and the total cut length, which set the machine time
- Tolerance and surface callout, since each extra skim pass adds time rather than cost per part only
- Whether the part is already hardened, because wire EDM cuts after heat treatment without distortion
- Start-hole positions and whether we drill them
- Whether the slug has to be retained or may drop free
- 2D DXF or the section of the 3D model that defines the profile
- Quantity, and whether the part is nested with others on the same plate
Send what you have — a model without a drawing, or a drawing without a model, is enough to start the review.
Frequently Asked Questions
Can you cut hardened tool steel and carbide?
Yes. Hardened tool steel, stainless and carbide are cut in the hardened state, which is the usual reason a profile is wire cut rather than milled. The cutting parameters follow the material and the thickness of the section.
How sharp can an internal corner be with wire EDM?
A wire-cut internal corner is limited by the wire rather than by a cutter radius, so it can be considerably sharper than a milled corner. Send the corner radius on the drawing and we confirm it with the quotation.
Do I have to draw in a start hole?
A closed internal profile needs a start hole so the wire can be threaded, and it is normally put on the drawing by the designer. Where it is missing we come back to you before cutting rather than changing the part.
What is wire EDM used for?
Cutting precise profiles, internal shapes and narrow slots in hardened steel, tool steel and exotic alloys that cannot be machined with conventional cutters — die inserts, punches, form profiles and prototype parts with sharp internal corners.
What tolerances can wire EDM hold?
±0.005 mm on critical features, verified on a CMM with a full report. General dimensions run at ±0.05–0.1 mm unless specified.
What surface finish does wire EDM produce?
Ra 0.4 μm as a working standard, down to Ra 0.1 μm with skim passes. The cut is burr-free — no secondary deburring of the profile edges.
Can you EDM after heat treatment?
Yes. Wire EDM is the standard finishing step for hardened tooling — the hardened part is cut to final profile without distortion, which is why it is the default for die and mold work.
Wire EDM or laser cutting — which fits my part?
Wire EDM wins on thick material, tight internal corners and higher precision; laser is faster on thin sheet but leaves a heat-affected zone and larger kerf. For functional profiles in hardened material, EDM is the reliable choice.
Do you provide CMM reports with EDM parts?
Yes. Every batch is inspected on a CMM with a free FAI report on your first order, and we report measured values on critical dimensions.
PRICING
What drives the price of Wire EDM
Wire EDM is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.
Have a Similar Part in Mind?
Send us your drawing — we review within 48h and return a quote with lead time.
Get a Quote →