CNC Turning: What Tolerances and Finishes Can You Hold on Rotational Parts?

CNC Turning at TruPart Precision (Dongguan, China) is quoted from the drawing: tolerance ±0.005 mm on critical diameters; surface finish Ra 0.8–1.6 μm (grinding to Ra 0.4); materials Aluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, PEEK/POM; batch 1–10,000+ (prototype to production). Every batch is verified — CMM, FAI report with measured values. A drawing review returns a quotation with unit price, machining route, lead time and freight within 48 hours, and there is no minimum order quantity.

  • TruPart Precision holds ±0.005 mm on critical diameters on CNC Turning work, and the measured values are reported per feature on a CMM.
  • Surface finish for CNC Turning is Ra 0.8–1.6 μm (grinding to Ra 0.4) as machined; finer finishes are quoted on request rather than assumed.
  • Materials used for CNC Turning: Aluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, PEEK/POM.
  • Batch sizes for CNC Turning range 1–10,000+ (prototype to production) — quantity changes the unit price rather than the process.
  • Inspection for CNC Turning: CMM, FAI report with measured values.
  • CNC Turning at TruPart Precision is quoted from the drawing; a prototype is priced on the same route as a production batch.
  • The Dongguan plant that machines CNC Turning holds ISO 9001:2015 certificate 93726Q00307R001.

What We Hold on Your Parts

Every number above is what we hold on your parts — CMM-verified, with free FAI on your first order.

Tolerance±0.005 mm on critical diameters
Surface finishRa 0.8–1.6 μm (grinding to Ra 0.4)
Size rangePrototype to production — send your drawing for a machine-envelope check
MaterialsAluminum 6061/7075, stainless 303/304/316, Ti-6Al-4V, brass, PEEK/POM
EquipmentCNC turning centers, turn-mill, Swiss-type
Batch1–10,000+ (prototype to production)
InspectionCMM, FAI report with measured values

Procurement facts — fixed before you order

ItemWhat is fixed
Minimum orderNo minimum order quantity. A single part and a production batch run through the same route.
QuotationWithin 48 hours of a drawing or STEP file: unit price, machining route, setup, packed weight and freight itemised.
Prototype lead time5–7 business days after drawing approval.
Production lead timeConfirmed per part and quantity in the quotation, not a catalogue figure.
IncotermsEXW, DDP or air. Freight is quoted before the order, not billed after it.
DocumentationMaterial certificate to EN 10204 3.1 with mill and heat number; CMM report with measured values; FAI report on a new part.

Batch range as stated on this page: 1–10,000+ (prototype to production)

What moves the unit price of CNC turning

A machined part is priced by the work it contains, not by its weight. Five drivers move the number, in this order of magnitude:

Cost driverRises whenEffect on unit price
SetupsFeatures sit on more than one face, or the datum has to be re-establishedHigh
Tolerance±0.005 mm appears on every dimension instead of only the critical onesMedium to high
Stock removalThe part is cut from solid bar or plate instead of a near-net blankMedium
Surface finishRa 0.4 µm or tighter, or a coating applied after machiningMedium
Batch sizeOne part carries the whole setup; 100 parts share itHigh at quantity 1, falls with volume

These are magnitudes, not prices. The quotation carries the actual numbers for your drawing, line by line.

What the quotation contains

Line in the quotationWhy it matters
Unit price at your quantityThe same part at 1, 100 and 1,000 pieces priced separately
Setup and tooling, listed separatelyOne-time charges are not folded into the unit price
Machining route and lead timeYou see which operations decide the date
Packed weight and carton sizeFreight can be calculated before you commit
Freight: EXW, DDP or airLanded cost known before the order
  • CNC turning at TruPart Precision holds tolerances of ±0.005 mm on critical diameters — measured on a CMM and reported as measured values with every batch.
  • A machined part is priced by setups, stock removal and tolerance, not by its weight.
  • TruPart Precision returns a CNC turning quotation within 48 hours of a drawing, with the machining route and freight itemised.

Where a turned part actually loses its tolerance

A turned part rarely fails on the machine that cut it. It drifts because the tool pushes the workpiece away from the cut, because a second operation re-chucks it against a new datum, or because heat treatment and coating moved it after the finish cut.

  • Deflection: turning between centres or Swiss-type guide-bushing support holds the diameter along the whole length, not only at the chuck
  • Re-chucking: cross-holes, flats and slots cut in the same cycle remove a second operation and the datum error that comes with it
  • Post-process growth: parts that are hardened, anodized or plated after turning are finished with the growth and distortion allowed for

Shafts, bushings, pins, dowels, set screws and hydraulic fittings are turned parts, and most of them arrive in the 1–100 piece range that makes up around 70% of the requests we receive.

Four things on the drawing decide a turning price

A turning quote is settled by the material grade, the diameter and length, the tightest callout, and the quantity you will reorder. Everything else is detail on top of those four.

  • Material grade as written on the drawing — 303, 304, 316, 316L, 17-4PH, 4140, 42CrMo, C45, brass or bronze
  • Quantity per batch and per year, so the price ladder follows your real order pattern
  • Finish and treatment: passivation, electroless nickel, hard chrome, phosphating, black oxide or anodizing
  • The dimensions your incoming inspection will check

No material substitution without your written agreement — where the drawing names a grade, that grade is what gets machined and what appears on the material certificate.

When a turned part is really a turn-mill part

A turned part that also carries cross-drilling, an axial slot, a milled flat or an off-centre hole normally costs two operations: turn it, then put it back in a milling machine. A turn-mill machine does both in one cycle from one datum.

  • Cross-holes, flats, slots and threads machined without re-clamping
  • Concentricity between the turned diameter and the milled feature held from a single datum
  • One setup means one fixture, one lead time and one inspection report

Where a part is too slender to be turned conventionally, the same work moves to Swiss-type turning, which cuts close to the guide bushing instead of at the end of a long overhang.

One-off shafts and repeat orders, priced the same way

A single turned sample and a 500-piece reorder go through the same drawing review and the same inspection — only the price per piece changes. Programmes and setup sheets stay on file, so a repeat order is quoted from the route that has already run.

Every batch ships with a CMM dimensional report listing measured values on the critical diameters, a free first article inspection report on a new part, and material certificates to EN 10204 3.1. Where the order is DDP, one invoice covers export, freight, customs and delivery.

From our historical RFQ data, around 70% of incoming part requests fall within 1–100 pieces. We support both prototype batches and volume production with no minimum-order requirement. Submit your drawing for feasibility evaluation.

What to send for a turning quotation

A turned part is priced on the bar it comes from and the number of operations after the first cut.

  1. Maximum outside diameter, so the bar stock size and the machine can be fixed
  2. Length and the length-to-diameter ratio, because slender parts need support and slower passes
  3. Features that need live tooling — cross holes, flats, slots — and their tolerance
  4. Thread specification and whether it is cut or rolled
  5. Tolerance on diameter, roundness and concentricity, feature by feature
  6. Material form: bar, forging or casting, and whether we buy the stock
  7. Quantity and whether the part repeats, so the cam or the programme is kept on file

Send what you have — a model without a drawing, or a drawing without a model, is enough to start the review.

Frequently Asked Questions

  • What is the difference between CNC turning and turn-mill machining?

    CNC turning cuts a rotational part with a single-point tool. Turn-mill machining adds driven tools to the same machine, so cross-holes, flats and slots are cut in the same cycle as the diameter — no second clamping and no datum error from re-chucking.

  • Which stainless grades do you turn?

    303, 304, 316 and 316L are the grades that come in most often, with 17-4PH where higher strength is needed. Where the drawing names a grade, no substitution is made, and the certificate shows the grade and heat number.

  • Do turned parts come with material certificates?

    Yes. Material certificates to EN 10204 3.1 naming the mill and heat number ship with the batch, and the CMM dimensional report lists measured values on the critical diameters. Every new part also gets a free first article inspection report.

  • What tolerance can CNC turning hold on diameters?

    ±0.005 mm on critical diameters, verified on a CMM with full report. General dimensions run at ±0.05–0.1 mm unless specified.

  • When should I choose turn-mill instead of turning?

    Parts with rotation plus off-axis features — cross holes, keyways, milled flats — are done in one setup on a turn-mill, avoiding transfer error between machines.

  • Can you machine thin-wall bushings without distortion?

    Yes. Thin-wall parts use controlled clamping and finishing passes so roundness holds within specification — CMM report included.

  • How does batch size affect turning price?

    Setup and programming dominate small batches; from 50 pieces the unit price drops 40–60% as setup cost spreads. No MOQ.

  • What surface finish is standard after turning?

    Ra 0.8–1.6 μm as standard; grinding reaches Ra 0.4 μm where required.

What buyers actually asked us this autumn

Verbatim lines from enquiries received between August and November 2026; buyer names and companies are withheld. Lines without quotation marks are summarised from the drawing or from the buyer’s own email.

Three M22 alloy-steel threaded parts, four pieces each, twelve pieces in total, ship date 9 November 2026.

Buyer reply to our EDM · damper manufacturer, United Kingdom · Sep 2026

“please provide me detailed quotation”

Reply to our first email · CTO, Russia · Aug 2026

What drives the price of CNC Turning

CNC Turning is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.

Have a Similar Part in Mind?

Send us your drawing — we review within 48h and return a quote with lead time.

Get a Quote →