Most enquiries get easier once you open the drawing. This one got harder in a useful way. The part is a main-spindle housing: Ø483 mm at its widest, roughly 405 mm long, in 316 stainless, and the quantity field says one piece. The title block says Stainless Steel 316. A note further down says CAST MATERIAL (316). Those two lines together decide almost everything about how the part is made and what it costs.

At a Glance
| Industry | Spindle and rotating assemblies for machine tools (United Kingdom) |
|---|---|
| Part | Main spindle housing, option 1, revision 2 — turned and bored body with bearing seats |
| Material | 316 stainless steel; the drawing notes CAST MATERIAL (316) |
| Envelope | Ø483 mm × approx. 405 mm |
| Quantity | 1 piece |
| Critical features | Ø320 / Ø300 mm bearing seats at 0.01–0.02 mm; Ø315 mm sealing face at 0.01–0.02 mm |
| Blank comparison | Solid bar: approx. 74 litres, about 592 kg · near-net sand casting: estimated 200–270 kg |
| What we delivered | Blank-route comparison, tolerance feasibility written out, and a two-path proposal instead of a single price |
| Status | Under costing; three technical points awaiting the customer's decision |
The Customer
A UK engineering company building spindle assemblies. They machine the rotating group themselves and outsource the housing — a part where the bore geometry sets the running accuracy of everything inside it. They sent one piece first, which is the sensible way to buy a casting: prove the geometry and the fit before committing to a pattern and a batch.
The Challenge
- One piece against a casting note. A sand pattern and a first-article casting only make sense across a batch. At one piece, the pattern cost sits entirely on that single part.
- Solid bar is not a cheap fallback. The envelope converts to roughly 74 litres of steel — about 592 kg of 316 bar before the first cut. Most of that becomes chips.
- 0.01–0.02 mm bearing seats on a 483 mm body. That is a grinding tolerance, not a turning tolerance, and it has to survive the fixture and the thermal history of a part this size.
- A very large thread on the mating shaft. M218 × 3.0 — 6g, with a note that tooling or mating parts may need to be supplied. Threads that size are made with a specific method and measured with a specific gauge.
- A dissimilar-metal fit in the same assembly. The slip-ring shaft is PB1 phosphor bronze with a 316 sleeve pressed on at Ø316.5 and ground to Ø315 after assembly. The press fit and the final grind are one operation, not two.
Our Approach
- We costed the blank before we costed the part. Solid bar came out at about 592 kg against an estimated 200–270 kg for a near-net sand casting. Neither number is a price — both are inputs the customer needs to see, because the gap between them is larger than most machining differences.
- We treated CAST as a note, not a locked process. The title block specifies 316 and does not prescribe a manufacturing method; the Chinese note adds the casting requirement. That is a point to confirm in writing with the customer rather than assume in either direction.
- We wrote the tolerance path out instead of quoting a number we cannot hold. Bearing seats at 0.01–0.02 mm on this size are a grinding operation. The honest routes are: supply semi-finished with 0.3–0.5 mm grinding allowance for the customer to finish, or work with a partner shop that grinds at this diameter — not to promise 0.01 mm and deliver 0.05.
- We separated the two parts of the assembly. The housing and the bronze shaft with its pressed sleeve are costed as two questions, because the press fit, the post-assembly grind to Ø315 and the M218 thread each carry their own risk.

Where the Drawing Met the Machine
| What the drawing asked for | What we could actually stand behind |
|---|---|
| 316 stainless, CAST MATERIAL in the notes | Confirmed with the customer which requirement governs; a casting needs a pattern and a batch, one piece does not justify it |
| Ø483 × 405 mm envelope, one piece | Blank route compared: about 592 kg solid bar versus an estimated 200–270 kg casting — the choice changes the price more than the machining does |
| Bearing seats 0.01–0.02 mm | Grinding, not turning. Offered semi-finished with 0.3–0.5 mm allowance, or a partner grinding route at this diameter |
| Ø315 mm sealing face, 0.01–0.02 mm | Same path as the bearing seats — the finish grind follows the press fit, not the turning operation |
| M218 × 3.0 — 6g thread | Method and gauge named in the offer, with the tooling/mating-part question raised before the order rather than after |
A quotation that promises 0.01 mm on a half-metre stainless body and then delivers 0.05 mm is worse than a quotation that says where the limit is. The customer can work with a stated limit. They cannot work with a surprise at incoming inspection.
What the Customer Received
| Blank comparison | Bar versus casting, by weight and by what each route implies for tooling and lead time |
|---|---|
| Tolerance feasibility | Which features we hold in turning, which need grinding, and what allowance to leave if they finish in-house |
| Two-path proposal | One route with the customer finishing the critical bores, one route through a grinding partner — priced as alternatives, not as a single take-it-or-leave-it number |
| Open questions in writing | Casting versus bar, the M218 thread tooling, and the press-fit sequence on the bronze shaft |
Status
This part is still in costing. Three things are open and they are all on the technical side, not the commercial side: whether the housing is bought as a casting or from bar, how the bearing seats are finished, and what happens with the M218 thread tooling. No order has been placed and no price has been sent as final.
The work that is done is the part that usually gets skipped: the blank was calculated rather than guessed, the tolerance was tested against what the process can actually hold, and the customer has the numbers needed to choose a route.
Frequently Asked Questions
Can you machine a 483 mm stainless housing from solid bar?
It is possible, but the blank is roughly 592 kg for a finished part of a fraction of that, and most of the material becomes chips. On a single piece the casting route is usually the one worth comparing first — which is why we calculate both instead of quoting the easier one.
Can you hold 0.01 mm on a bearing seat at this diameter?
Not by turning. At this size that is a grinding tolerance, and we say so rather than quoting it. The practical routes are semi-finished supply with 0.3–0.5 mm grinding allowance for you to finish, or a partner grinding operation at this diameter.
The drawing says CAST MATERIAL — does that mean you must cast it?
It means the requirement has to be confirmed. The title block specifies 316 stainless without prescribing a process; the casting note is an additional requirement. On one piece, a pattern and a first casting carry a cost that has to be discussed openly before it is quoted.
How do you handle a press fit that gets ground after assembly?
As one sequence, not two operations. The sleeve is pressed at Ø316.5 and ground to Ø315 after assembly, so the finishing allowance and the fixture have to be planned around the assembled part — the bore cannot be finished before the press fit and then expected to stay concentric.
What do you need to quote a single large part like this?
The 2D drawing with the tolerance block and any notes on material condition, the quantity you actually intend to buy, whether you can accept semi-finished supply for critical bores, and the inspection documentation you need. A 3D model helps for the blank calculation but not for the tolerances.