Milled Parts from China: Aluminium Housings, Ra 1.6 μm, Quote in 48 Hours

Milled Parts from China at TruPart Precision (Dongguan, China) is quoted from the drawing: tolerance ±0.01 mm general, ±0.005 mm on critical features; surface finish Ra 1.6 μm typical as milled; Ra 0.8–3.2 μm range; finer by grinding; materials Aluminium 6061/7075/6082, stainless 303/304/316L, steel 1045/4140, titanium, brass, POM/PEEK/Delrin; batch 1–5,000+ pieces. Every batch is verified — CMM report with measured values; free FAI report on a new part. A drawing review returns a quotation with unit price, machining route, lead time and freight within 48 hours, and there is no minimum order quantity.

  • TruPart Precision holds ±0.01 mm general, ±0.005 mm on critical features on Milled Parts from China work, and the measured values are reported per feature on a CMM.
  • Surface finish for Milled Parts from China is Ra 1.6 μm typical as milled; Ra 0.8–3.2 μm range; finer by grinding as machined; finer finishes are quoted on request rather than assumed.
  • Materials used for Milled Parts from China: Aluminium 6061/7075/6082, stainless 303/304/316L, steel 1045/4140, titanium, brass, POM/PEEK/Delrin.
  • Batch sizes for Milled Parts from China range 1–5,000+ pieces — quantity changes the unit price rather than the process.
  • Inspection for Milled Parts from China: CMM report with measured values; free FAI report on a new part.
  • Milled Parts from China at TruPart Precision is quoted from the drawing; a prototype is priced on the same route as a production batch.
  • The Dongguan plant that machines Milled Parts from China holds ISO 9001:2015 certificate 93726Q00307R001.

What a milled part quotation from China should contain

A milled part is priced by the number of setups the geometry forces, the volume of material that leaves as chips, and how tight the critical callouts are. None of that is visible in a one-line price, so the quotation has to show the route behind it.

We send the unit price at your quantity, the machining route (3-axis or 5-axis, how many setups), the lead time, one-time setup and tooling charges separately, packed weight and carton dimensions, and shipping as EXW or DDP — within 48 hours of drawing review.

  • Milled aluminium parts in 6061 or 7075 hold ±0.005 mm on critical features and Ra 0.8–3.2 μm as machined, verified on a CMM.
  • A 5-axis setup cuts bores, sealing faces and mounting holes from the same datum, so a compound-angle part does not pick up re-clamp error.
  • There is no minimum order quantity; a single plate and a 5,000-piece run are quoted from the same setup sheet.

Procurement facts — fixed before you order

ItemWhat is fixed
Minimum orderNo minimum order quantity. A single part and a production batch run through the same route.
QuotationWithin 48 hours of a drawing or STEP file: unit price, machining route, setup, packed weight and freight itemised.
Prototype lead time5–7 business days after drawing approval.
Production lead timeConfirmed per part and quantity in the quotation, not a catalogue figure.
IncotermsEXW, DDP or air. Freight is quoted before the order, not billed after it.
DocumentationMaterial certificate to EN 10204 3.1 with mill and heat number; CMM report with measured values; FAI report on a new part.

Batch range as stated on this page: 1–5,000+ pieces

What moves the unit price of milled part manufacturing

A machined part is priced by the work it contains, not by its weight. Five drivers move the number, in this order of magnitude:

Cost driverRises whenEffect on unit price
SetupsFeatures sit on more than one face, or the datum has to be re-establishedHigh
Tolerance±0.005 mm appears on every dimension instead of only the critical onesMedium to high
Stock removalThe part is cut from solid bar or plate instead of a near-net blankMedium
Surface finishRa 0.4 µm or tighter, or a coating applied after machiningMedium
Batch sizeOne part carries the whole setup; 100 parts share itHigh at quantity 1, falls with volume

These are magnitudes, not prices. The quotation carries the actual numbers for your drawing, line by line.

What the quotation contains

Line in the quotationWhy it matters
Unit price at your quantityThe same part at 1, 100 and 1,000 pieces priced separately
Setup and tooling, listed separatelyOne-time charges are not folded into the unit price
Machining route and lead timeYou see which operations decide the date
Packed weight and carton sizeFreight can be calculated before you commit
Freight: EXW, DDP or airLanded cost known before the order
  • Milled part manufacturing at TruPart Precision holds tolerances of ±0.01 mm general, ±0.005 mm on critical features — measured on a CMM and reported as measured values with every batch.
  • A machined part is priced by setups, stock removal and tolerance, not by its weight.
  • TruPart Precision returns a milled part manufacturing quotation within 48 hours of a drawing, with the machining route and freight itemised.

The milling specification we quote against

Tolerance±0.01 mm general, ±0.005 mm on critical features
Surface finishRa 1.6 μm typical as milled; Ra 0.8–3.2 μm range; finer by grinding
Axes3-axis VMC; 5-axis machining centres for compound angles
PartsPlates, housings, valve bodies and manifolds, covers, brackets, impellers
MaterialsAluminium 6061/7075/6082, stainless 303/304/316L, steel 1045/4140, titanium, brass, POM/PEEK/Delrin
Batch1–5,000+ pieces
InspectionCMM report with measured values; free FAI report on a new part
CertificatesEN 10204 3.1 mill certificate with mill and heat number

Six checks before you order milled parts from China

These are the six questions that separate a machine shop from a broker, and each one has a factual answer you can verify before the first order.

  1. Who runs the machine — Ask which factory mills the part and for a photo of the setup. A broker forwards your drawing and adds a margin; a shop tells you the fixture and the number of setups.
  2. The drawing was reviewed, not just priced — A real quotation names the features that drive cost — the deep pocket, the ±0.005 mm bore, the compound angle. A price with no comments means nobody looked at the drawing.
  3. Measured values on the critical features — Ask for a CMM report from a comparable job with the readings visible, including position and flatness where the drawing calls them out.
  4. Where 3-axis ends and 5-axis starts — If the supplier cannot explain which of your features needs a fourth setup, the quote will either be wrong or padded. One 5-axis setup is usually cheaper than three re-clamps on a tight part.
  5. What ships with the batch — CMM report with measured values, EN 10204 3.1 certificate with mill and heat number, and a free FAI on a new part — requested in the quotation, not after delivery.
  6. Order size and terms — No minimum order, quantity only changing the unit price; shipping quoted as EXW or DDP with duty and delivery named before the order.

From drawing to delivered milled parts

  1. Send the drawing — 2D PDF with tolerances plus STEP. Call out sealing faces, datum structure and any surface finish requirement.
  2. Drawing review and quotation — 48 hours. Unit price, route, number of setups, lead time and the cost drivers named in writing.
  3. First article — The first part is measured and reported before the run continues; the FAI report is free on a new part.
  4. Production and inspection — Certified stock, CMM inspection, measured values recorded for the critical features.
  5. Shipping — DDP door-to-door with one invoice covering export, freight, duty and delivery, or EXW from Dongguan.

What decides the price of a milled part

A milled part is not priced by its weight. It is priced by how many setups the geometry forces, how much of the stock ends up as chips, and how tight the critical callouts are. Two plates with the same outline can differ several times over on those three points alone.

  • Setups: features on five faces mean one 5-axis setup instead of three re-clamps and a fixture for each
  • Material removal: a part cut from solid plate carries cutting time that a near-net blank would not have
  • Tolerance: ±0.005 mm on critical features is routine; the same callout on every dimension adds inspection time without adding function
  • Finish: an Ra 1.6 μm as-milled face needs no extra pass; a Ra 0.4 μm sealing face needs grinding or a separate finishing operation

Frequently asked questions

  • Which Chinese machine shop mills hydraulic valve bodies?

    We mill hydraulic valve bodies and manifold blocks in Dongguan: 6061/7075 aluminium, 1045/4140 steel and 316L stainless, ±0.005 mm on port locations and seal faces, CMM-measured, with thread gauges for NPT, BSP and metric ports.

  • What does CNC milling of aluminium parts cost in China?

    The price follows the machining time, not the aluminium: bar or plate cost is a small share of a milled housing. A part with three setups and a ±0.005 mm bore costs more in labour than in material, and the quotation shows both lines separately so you can see which one you are paying for.

  • How fast can I get a quote for 100 milled aluminium parts?

    48 hours after drawing review, with the unit price at 100 pieces, the setup charge listed once, and shipping quoted before the order.

  • What Ra value can CNC milling achieve?

    Ra 1.6 μm is typical as milled and Ra 0.8 μm is achievable on 5-axis contour finishing with a finishing pass. A sealing face at Ra 0.4 μm is ground rather than milled.

  • Can you mill POM and engineering plastics?

    Yes: POM/Delrin, PEEK, ABS and similar plastics, machined with sharp tooling and controlled clamping so the part does not stress-relieve out of tolerance after machining.

  • Do you machine from customer-supplied castings or forgings?

    Yes. Supplied castings and forgings are fixtured and machined, and the same part can also be produced from solid plate. For prototypes and small batches, plate is usually faster and cheaper; castings pay off when the geometry would waste a lot of material.

  • What is the difference between 3-axis and 5-axis for my part?

    A part with pockets on one face and a flat back is a 3-axis job. A part whose bores, sealing faces or contour faces sit at compound angles is 5-axis work, because every extra re-clamp adds a datum error on top of the tolerance you asked for.

  • How is shipping handled?

    EXW Dongguan, or DDP door-to-door with one invoice covering export, freight, duty and delivery.

What drives the price of Milled Parts from China

Milled Parts from China is quoted from the drawing, not from a catalogue: material block size, how many setups the geometry forces, the tolerance class and the batch size set the unit price. Machine-hour rates, material block prices and indicative bands at 1, 10 and 100 pieces are published in our CNC machining cost breakdown, so the number can be checked before a drawing is sent. A drawing review returns a quotation within 48 hours, with no minimum order quantity.

A similar part in mind?

Send the drawing — we review it within 48 hours and come back with a quotation and a lead time.

Request a quote →