Why is the quote higher than you expected?
Every week we get RFQs where the buyer has a number in their head, and every week the gap between that number and the quote comes down to the same five things: material, machine time, setup, tolerance, and quantity. None of them is a mystery. Once you see how a quote is built, you can design and spec parts that quote lower — and you will know exactly what to ask a supplier to justify a number.
Why does material set the floor of a CNC quote?
Material is usually 15-40% of the part price. Aluminum 6061 is cheap; 7075, stainless 316, titanium and copper alloys climb fast. Small quantities pay for material from the minimum bar or plate purchase, so an exotic alloy on a 10-piece run hits hard. If the drawing over-specifies material (7075 where 6061 works), the quote carries the penalty all the way through.
Where does machine time sit inside the quote?
Machine time is the biggest line on most quotes. It splits into two kinds: cutting time, which depends on part complexity, and setup time, which depends on how many operations and fixtures the part needs. A part that needs one operation in a 5-axis machine prices very differently from the same part needing three setups on three machines. Every feature that forces a new setup — a back-side feature, a fifth-axis angle, a second chucking — adds real money.
What do tolerance and surface finish add to the price?
Tight tolerances cost in three places: slower machining, more inspection, and more scrap risk. A general tolerance part (0.1 mm) machines fast and gets a spot check. A ±0.005 mm critical dimension means careful finishing passes, CMM inspection, and a higher risk of losing parts — all priced in. Surface finish works the same way: Ra 1.6 is free, Ra 0.4 needs grinding or fine finishing. Spec precision where the assembly uses it, and the quote drops.
| Cost Driver | Cheap Version | Expensive Version | Impact |
|---|---|---|---|
| Material | 6061 / 1045 / 12L14 | Titanium / 316L / 7075 | 15-40% of price |
| Complexity | 2.5-axis, one setup | 5-axis, multiple ops | Machine time |
| Tolerance | ±0.1 mm general | ±0.005 mm critical | Inspection + scrap risk |
| Finish | Ra 1.6 machined | Ra 0.4 ground | Extra process |
| Quantity | 500+ pcs | 1-20 pcs | Setup amortization |
How does quantity change the price per part?
Setup and programming cost the same for 1 piece or 1,000. Spread across 10 pieces they dominate the price; spread across 500 they nearly vanish. This is why the per-piece number on small batches shocks buyers — it is not a penalty, it is division. If your real volume is 200 parts a year, say so. We quote against the annual picture, and the price per piece for a combined prototype-plus-production agreement is often far better than one-off pricing.
How do you get the best CNC quote?
A complete RFQ gets the best number: full drawing with GD&T, material grade and condition, quantity and expected annual volume, surface finish requirements, and any special processes. What kills pricing speed: missing material spec, unmarked critical tolerances, and drawings that leave the shop guessing. And ask the supplier what drives the price on your part — a good shop will tell you exactly where the money is, and usually where to cut it.
Send us your drawing and we will return a quote with the cost breakdown and drawing notes — you will see exactly what drives your price, and how to lower it.
Why should a quote be a conversation, not a verdict?
A good machining quote is the start of a dialogue, not a take-it-or-leave-it number. If the price is higher than your target, ask where the money goes — the answer is usually one line you can act on: loosen this tolerance, change this material, combine these variants into one program. Shops that explain their numbers are shops that can work with you to hit a target. Shops that only defend them are quoting by formula. You want the first kind.
Frequently Asked Questions
What is the biggest factor in CNC machining cost?
Machine time — cutting time plus the number of setups. Complexity that forces extra setups or five-axis work drives cost more than almost anything else.
Why are prototype quantities so expensive per piece?
Setup, programming and first-article inspection cost the same for 1 or 1,000 pieces. On small batches those fixed costs are divided by few parts.
Do tighter tolerances really increase price?
Yes — slower machining, more inspection and higher scrap risk. Spec ±0.005 mm only where the assembly needs it; general tolerances quote significantly lower.
How much does material choice affect the quote?
Material is typically 15-40% of part price. Exotic alloys on small runs are especially expensive because you pay for the minimum stock purchase.
What information makes quotes faster and cheaper?
A complete drawing with GD&T, material grade, quantity and annual volume, surface finish specs, and special process requirements. Missing info forces conservative padding.
Need this kind of part machined?
Send a drawing — quote in 48 hours. No minimum order; one piece is fine.